Results 1 to 10 of 10

Thread: Project: Shitter

  1. #1
    Join Date
    Jul 2005
    Location
    The Forest Moon of Endor.
    Posts
    16,998
    Images
    117

    Project: Shitter

    Inspired by Geoff and Trev, I will actually attempt to build a bike.

    Today I've been to the 'shed' to remind myself what I've got....

    FCR41MX (I think it's a 41, might be a 42), with a nice shiny alloy tube to it will clear the frame when mounted to the standard intake manifold





    A few barrels...



    There's another 4 in various states of repair in my garage.

    This one might clean up, had a teeny bit of a seize....


  2. #2
    Join Date
    Jul 2005
    Location
    The Forest Moon of Endor.
    Posts
    16,998
    Images
    117
    The best head...



    See that tiny crack between on of the valve seats and the spark plug hole, that's a known weak spot on the 500/600/650 heads, dunno what to do about that at the moment. It's a shame because that head has new valve guides and HD valve springs and Kibblewhite valves in it at the moment.

    The cases that match the frame...



    I've got a gearbox from a 650 Dominator to go in as the original 500 box kept jumping out of 5th under power.

    Spot the difference....



    One is the standard XBR crank, the other a XL600 crank, the XL didn't have a leccy boot so the bit the flywheel goes on is shorter, no starter gear on the flywheel.

    Means I and junk all the leccy start stuff, fit the lighter XL flywheel and use the magnesium side case without the starter clutch in it.

  3. #3
    Join Date
    Jul 2005
    Location
    The Forest Moon of Endor.
    Posts
    16,998
    Images
    117
    Standard flywheel cover....



    you can see the gear/clutch of the leccy boot at the top, looks like a seperate casting, but it's all part of the side cover.

    Which will be replaced by this....



    I'm undecided as to if I'm going to use this brand new conrod, it's a prox one and there's not a lot of play in the rod on the XL600 crank...




    Bit's still to find....

    I've got a Joy engineering replica of the HRC RS600 flat tracker camshaft, an XR500 high compression wiseco piston, which seized in the bores, I'm pretty sure it only needs new rings and will clean up, but I can't spot it.

  4. #4
    Join Date
    Jul 2005
    Location
    The Forest Moon of Endor.
    Posts
    16,998
    Images
    117
    Things to buy...

    a pair of honda quality crank bearings, according to the workshop manual, they have to be replaced EVERY time the cases are split!

    Some oil seals and a full gasket set.

    I hope to have the engine finished by 2015.

  5. #5
    Join Date
    Jun 2005
    Location
    The Republic of Barnes
    Posts
    39,891
    Images
    55
    Blog Entries
    71
    Gay.

  6. #6
    That's a pretty tight deadline.

    Comments on this post
    Y282 agrees:

  7. #7
    Join Date
    Jul 2005
    Location
    The Forest Moon of Endor.
    Posts
    16,998
    Images
    117
    Engine finished 2015, rest of bike some time 2023, maybe.

  8. #8
    Missed this. An interesting project and in the appropriate forum to boot.

    You going for the flat tracker look or the faux Goldstar(ish) route Giles?. What sort of power could the engine put out with all those tuning bits you have. Nice and light and 50 bhp would make a fun bike.

    Cheers Geoff

  9. #9
    Join Date
    Jul 2005
    Location
    The Forest Moon of Endor.
    Posts
    16,998
    Images
    117
    Honda figures were 44bhp, but I think they make about 36bhp stock at the wheel.

    The GB500 was the 'retro' version of the XBR which looked a bit like a Goldie, I quite like the idea of an alloy tank/seat unit but we'll have to wait and see.... in 2023.

  10. #10
    Join Date
    Jun 2005
    Location
    The Republic of Barnes
    Posts
    39,891
    Images
    55
    Blog Entries
    71
    Jesus fucking wept.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •